ADG528FBP
| Parameters | |
|---|---|
| Additional Feature | ACTIVE OVERVOLTAGE PROTECTION |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 3.3mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG528 |
| Pin Count | 20 |
| Operating Supply Voltage | 15V |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 10.8V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Power Dissipation | 3mW |
| Max Supply Current | 200μA |
| Throw Configuration | DPST |
| Turn On Delay Time | 250 ns |
| Number of Inputs | 8 |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 300Ohm Typ |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 50pF |
| On-state Resistance Match-Nom | 15Ohm |
| Switch Time (Ton, Toff) (Max) | 250ns, 250ns |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 15 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 400ns |
| Switch-off Time-Max | 400ns |
| Signal Current-Max | 0.02A |
| Voltage - Supply, Dual (V±) | ±15V |
| Height Seated (Max) | 4.57mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Surface Mount |
| Package / Case | 20-LCC (J-Lead) |
| Surface Mount | YES |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 300Ohm |
ADG528FBP Overview
Due to its 20-LCC (J-Lead) packaging, the electronic part is convenient for international shipping. The advanced packaging method Tube provides high reliability. It is mounted in the position Surface Mount. There is 8:1 ratio between the number of multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. 20 terminations have been made so far. A high-quality output is provided by the electrical component's 8 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. 20 pins are injected to the electronic part body. A total of 1 circuits make up this switch device. Try searching with ADG528 to find analog multiplexer variants. Internally, this switch multiplexer has a resistance of 300Ohm. The datasheets for the 20 pins explain the functions. This switch device is a typical Multiplexer or Switches. A voltage higher than 16.5V should not normally be supplied to the switches. There should be 10.8V voltage fed to the electrical part below 10.8V. A digital multiplexer may suffer damage if voltage is applied above 200μA. Despite this switch's dual supply capability, its voltage should not exceed 22V. It is integrated with a SINGLE-ENDED MULTIPLEXER analog IC. There is a voltage range of 15V operating voltages for the electrical part. Operating the 8 inputs requires 8 inputs. Additional features include: ACTIVE OVERVOLTAGE PROTECTION.
ADG528FBP Features
8 Channels
Additional Features: ACTIVE OVERVOLTAGE PROTECTION
ADG528FBP Applications
There are a lot of Analog Devices Inc. ADG528FBP Analog Switches & Multiplexers ICs applications.
- Microprocessor controlled systems
- Automatic test equipment
- SDH/SONET multiplexers
- E1 Network Equipment
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Communication systems
- Medical Instrumentation
- DSLAMs
- DSUs
- Private Branch Exchange (PBX)