ADG438FBRZ
| Parameters | |
|---|---|
| Factory Lead Time | 8 Weeks |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 400Ohm |
| Additional Feature | FAULT PROTECTED; OVERVOLTAGE PROTECTION |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 2.6mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG438 |
| Pin Count | 16 |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 15V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 50μA |
| Nominal Supply Current | 50μA |
| Power Dissipation | 2.6mW |
| Max Supply Current | 200μA |
| Throw Configuration | SPST |
| Propagation Delay | 220 ns |
| Turn On Delay Time | 250 ns |
| Number of Inputs | 8 |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 270Ohm Typ |
| High Level Output Current | 20mA |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 93 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 22pF |
| On-state Resistance Match-Nom | 8.1Ohm |
| Switch Time (Ton, Toff) (Max) | 230ns, 130ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 8.1 Ω |
| Crosstalk | -93dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 345ns |
| Drain to Source Resistance | 400Ohm |
| Signal Current-Max | 0.02A |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG438FBRZ Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). To ensure high reliability, a new packaging method Tube is used. Multiplexers like this are mounted in the Surface Mount position. 8:1 is the ratio of multiplexer to demultiplexer circuits. Operational temperature extended around -40°C~125°C TA. 16 terminations have been made so far. A electrical component with 8 channels is capable of high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. There are 16 pins injected into the electronic part body. There are 1 circuits in this multiplexer. Try searching with ADG438 if you're looking for variants. In this multiplexer, the internal resistance is 400Ohm. To find out what the 16 pins do, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. It is recommended to use 15V as the lowest voltage for the electrical part. The switch device would be able to operate with 50μA current. Put voltage above 200μA on the multiplexer to cause damage. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. There is an integrated analog IC SINGLE-ENDED MULTIPLEXER in the module. In order to operate the 8 inputs, there are several steps to follow. Check out the electrical component's additional features, such as the following: FAULT PROTECTED; OVERVOLTAGE PROTECTION. There is 400Ohm Drain to Source resistance on this electronic part.
ADG438FBRZ Features
8 Channels
50μA Supply Current
Additional Features: FAULT PROTECTED; OVERVOLTAGE PROTECTION
Drain-to-Source resistance: 400Ohm
ADG438FBRZ Applications
There are a lot of Analog Devices Inc. ADG438FBRZ Analog Switches & Multiplexers ICs applications.
- Switching Systems
- SDH
- Relay Replacement
- 65 V DACs
- USB 1.1 signal switching circuits
- CSU
- Routers
- DSUs
- Channel Banks
- Cell phones