Parameters |
Channel Capacitance (CS(off), CD(off)) |
5pF 50pF |
On-state Resistance Match-Nom |
4Ohm |
Switch Time (Ton, Toff) (Max) |
160ns, 150ns |
Charge Injection |
8pC |
Channel-to-Channel Matching (ΔRon) |
4 Ω |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
80Ohm |
Signal Current-Max |
0.02A |
Voltage - Supply, Dual (V±) |
±15V |
Height |
1.75mm |
Length |
10.2mm |
Width |
5.3mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
Factory Lead Time |
8 Weeks |
Lifecycle Status |
PRODUCTION (Last Updated: 2 weeks ago) |
Contact Plating |
Tin |
Mounting Type |
Surface Mount |
Package / Case |
28-SSOP (0.209, 5.30mm Width) |
Surface Mount |
YES |
Number of Pins |
28 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
3 (168 Hours) |
Number of Terminations |
28 |
ECCN Code |
EAR99 |
Resistance |
80Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
3.1mW |
Technology |
BICMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
15V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG426 |
Pin Count |
28 |
Operating Supply Voltage |
12V |
Number of Channels |
16 |
Interface |
Parallel |
Number of Circuits |
1 |
Max Supply Voltage |
25V |
Analog IC - Other Type |
SINGLE-ENDED MULTIPLEXER |
Operating Supply Current |
200μA |
Nominal Supply Current |
100μA |
Power Dissipation |
3.1mW |
Max Supply Current |
200μA |
Propagation Delay |
150 ns |
Turn On Delay Time |
240 ns |
Number of Inputs |
16 |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
110 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
80Ohm |
High Level Output Current |
20mA |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
16:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
ADG426BRSZ Overview
The electronic component is convenient to ship overseas because it is packed in a 28-SSOP (0.209, 5.30mm Width). In order to provide high reliability, an advanced packaging method Tube is used. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 16:1. Operating temperature extended to -40°C~85°C TA. Total terminations are 28. By its 16 channels, the electronic component provides high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. It is injected into the electrical part body with 28 pins. A total of 1 circuits make up this switch device. Try searching with ADG426 if you're looking for variants. This digital multiplexer has 80Ohm internal resistance. The functions of 28 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 25V. An operating current of 200μA would be sufficient for this switch device. It may damage the digital multiplexer if the voltage is higher than 200μA. Despite this switch device's dual supply capability, its voltage should not exceed 22V. With a SINGLE-ENDED MULTIPLEXER analog IC integrated into the board. It can operate from 12V operating voltages. There are 16 inputs to be operated. Resistivity from Drain to Source is 80Ohm for this electronic part.
ADG426BRSZ Features
16 Channels
200μA Supply Current
Drain-to-Source resistance: 80Ohm
ADG426BRSZ Applications
There are a lot of Analog Devices Inc. ADG426BRSZ Analog Switches & Multiplexers ICs applications.
- Cable PC
- Ultrasound
- Voice over IP/DSL – Integrated Access Devices, Smart
- PBXs
- Avionics
- Relay Replacement
- SDH/SONET multiplexers
- Access Concentrators
- Isolation
- Data switching