ADG407BPZ
| Parameters | |
|---|---|
| Factory Lead Time | 8 Weeks |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 28-LCC (J-Lead) |
| Surface Mount | YES |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 3.1mW |
| Technology | BICMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG407 |
| Pin Count | 28 |
| Operating Supply Voltage | 12V |
| Supply Voltage-Min (Vsup) | 13.5V |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 2 |
| Max Supply Voltage | 25V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Nominal Supply Current | 100μA |
| Power Dissipation | 3.1mW |
| Number of Inputs | 16 |
| Supply Current-Max (Isup) | 0.5mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 110 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 80Ohm |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 25pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Time (Ton, Toff) (Max) | 160ns, 150ns |
| Charge Injection | 8pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω |
| Crosstalk | -85dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 150ns |
| Switch-off Time-Max | 150ns |
| Drain to Source Resistance | 50Ohm |
| Neg Supply Voltage-Min (Vsup) | -13.5V |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.94mm |
| Length | 11.58mm |
| Width | 11.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG407BPZ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 28-LCC (J-Lead). To ensure high reliability, a new packaging method Tube is used. Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a ratio of 8:1. The operating temperature is extended to around -40°C~85°C TA. Totally, there are 28 terminations. By its 8 channels, the electronic component provides high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. A key feature of the 28 series is the inclusion of this electronic part as part of its design. The multiplexer consists of 2 circuits. Use ADG407 to search for variants of the digital switches. There is 50Ohm internal resistance in this digital multiplexer. To find out what the 28 pins do, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 25V. For this switch, a dual supply voltage is feasible, but it must not exceed 22VAn analog IC with the number DIFFERENTIAL MULTIPLEXER is integrated into this board. The electronic component can function from 12V. Among the inputs that can be operated are the 16 inputs. Drain to Source resistance is 50Ohm. To supply the switch device, a voltage of 13.5V must be applied.
ADG407BPZ Features
8 Channels
Drain-to-Source resistance: 50Ohm
ADG407BPZ Applications
There are a lot of Analog Devices Inc. ADG407BPZ Analog Switches & Multiplexers ICs applications.
- Audio and video signal routing
- Voice over IP/DSL – Integrated Access Devices, Smart
- ATM
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Digital Cross-Connects
- Avionics and Military Systems
- Communication systems
- Sample hold systems
- Communication systems
- Fiber In The Loop (FITL)