Parameters |
Factory Lead Time |
10 Weeks |
Lifecycle Status |
PRODUCTION (Last Updated: 3 weeks ago) |
Contact Plating |
Tin |
Mounting Type |
Surface Mount |
Package / Case |
24-TSSOP (0.173, 4.40mm Width) |
Surface Mount |
YES |
Number of Pins |
24 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
24 |
ECCN Code |
EAR99 |
Resistance |
11.5Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
2.8mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
8 |
Supply Voltage |
5V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
ADG1414 |
Pin Count |
24 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
12V |
Polarity |
Non-Inverting |
Number of Channels |
1 |
Interface |
Parallel |
Max Supply Voltage |
16.5V |
Min Supply Voltage |
4.5V |
Test Frequency |
1MHz |
Power Dissipation |
2.8mW |
Max Supply Current |
1μA |
Turn On Delay Time |
93 ns |
Number of Inputs |
8 |
Voltage - Supply, Single/Dual (±) |
12V ±4.5V~16.5V |
Supply Type |
Dual, Single |
Bandwidth |
256MHz |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
35 ns |
Max Dual Supply Voltage |
16.5V |
On-State Resistance (Max) |
11.5Ohm |
Min Dual Supply Voltage |
4.5V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
70 dB |
Current - Leakage (IS(off)) (Max) |
150pA |
Channel Capacitance (CS(off), CD(off)) |
8pF |
On-state Resistance Match-Nom |
0.6Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
93ns, 35ns |
Insertion Loss (dB) |
0.55 dB |
Charge Injection |
10pC |
Channel-to-Channel Matching (ΔRon) |
550m Ω |
Crosstalk |
-75dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
320ns |
Switch-off Time-Max |
70ns |
Normal Position |
NO |
Height |
1.2mm |
Length |
7.9mm |
Width |
4.5mm |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG1414BRUZ Overview
The electronic component is convenient to ship overseas because it is packed in a 24-TSSOP (0.173, 4.40mm Width). High reliability is achieved by using advanced packaging method Tube. The multiplexer is located in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of -40°C~125°C TA degrees Celsius. In total, there have been 24 terminations. The electronic part provides high-quality output because it has 1 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. An injection of 24 pins is performed into the body of the electrical component. Based on SPST - NO switching circuits, these analog multiplexers work. Try searching with ADG1414 to find analog multiplexer variants. An switch multiplexer with 11.5Ohm internal resistance has a value of 11.5Ohm. To find out what the 24 pins do, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 16.5V. Dual, Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 4.5V. A voltage higher than 1μA may cause damage to the switch multiplexer. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 16.5V. With dual power supplies, you should attach at least 4.5V. There is a voltage range of 12V operating voltages for the electrical part. A 8 input needs to be operated. A 256MHz-bandwidth can be used for data transfer.
ADG1414BRUZ Features
1 Channels
Switch Circuit: SPST - NO
Bandwidth: 256MHz
ADG1414BRUZ Applications
There are a lot of Analog Devices Inc. ADG1414BRUZ Analog Switches & Multiplexers ICs applications.
- FTTH
- DSLAMs
- Cable Modem
- Cross Connects
- ISDN NT1/TA
- Frame Relay Equipment
- Cable PC
- DVD-R
- Microprocessor controlled systems
- Cell phones