74LVX174M
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Supplier Device Package | 16-SOIC |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74LVX |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 2V~3.6V |
| Frequency | 55MHz |
| Base Part Number | 74LVX174 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 7 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 2V |
| Number of Bits | 6 |
| Clock Frequency | 95MHz |
| Propagation Delay | 22 ns |
| Turn On Delay Time | 9.3 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 4mA 4mA |
| Number of Bits per Element | 6 |
| Max Frequency | 55MHz |
| Max Propagation Delay @ V, Max CL | 12.8ns @ 3.3V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -4mA |
| Input Capacitance | 4pF |
| Low Level Output Current | 4mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 6 |
| Clock Edge Trigger Type | Positive Edge |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74LVX174M Overview
The flip flop is packaged in a case of 16-SOIC (0.154, 3.90mm Width). A package named Tubeincludes it. T flip flop uses Non-Invertedas its output configuration. The trigger it is configured with uses Positive Edge. It is mounted in the way of Surface Mount. The supply voltage is set to 2V~3.6V. Currently, the operating temperature is -40°C~85°C TA. D-Typeis the type of this D latch. FPGAs belonging to the 74LVXseries contain this type of chip. You should not exceed 95MHzin the output frequency of the device. In total, it contains 1 elements. It consumes 4μA of quiescent current without being affected by external factors. It is a member of the 74LVX174 family. There is 4pF input capacitance for this T flip flop. There is an electronic part mounted in the way of Surface Mount. This board has 16 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. An electronic part designed with 6bits is used in this application. Due to its superior flexibility, it uses 7 circuits. The JK flip flop is with 6 output lines to operate. This input has 3lines in it. In this case, the high level output current is set to -4mA. In the low level output current setting, the current is set to 4mA. Ideally, the operating temperature should be lower than 85°C. It is recommended that the operating temperature is higher than -40°C. Normally, it operates with a voltage of 2VV as its minimum supply voltage. The maximum supply voltage supported by the flip flop is 3.6V. This frequency can be achieved 55MHz.
74LVX174M Features
Tube package
74LVX series
16 pins
6 Bits
74LVX174M Applications
There are a lot of ON Semiconductor 74LVX174M Flip Flops applications.
- Clock pulse
- Test & Measurement
- Frequency Divider circuits
- Bounce elimination switch
- Data Synchronizers
- Patented noise
- Consumer
- Set-reset capability
- Functionally equivalent to the MC10/100EL29
- ESCC