74LVTH273SJX
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-SOP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74LVTH |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 2.7V~3.6V |
| Frequency | 150MHz |
| Base Part Number | 74LVTH273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 3.3V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 2.7V |
| Number of Bits | 8 |
| Clock Frequency | 150MHz |
| Propagation Delay | 5.5 ns |
| Turn On Delay Time | 4.9 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 190μA |
| Current - Output High, Low | 32mA 64mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 4.9ns @ 3.3V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -32mA |
| Input Capacitance | 3pF |
| Low Level Output Current | 64mA |
| Number of Input Lines | 4 |
| Number of Output Lines | 7 |
| Clock Edge Trigger Type | Positive Edge |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74LVTH273SJX Overview
The flip flop is packaged in 20-SOIC (0.209, 5.30mm Width). D flip flop is embedded in the Tape & Reel (TR) package. This output is configured with Non-Inverted. The trigger it is configured with uses Positive Edge. Surface Mountis positioned in the way of this electronic part. The supply voltage is set to 2.7V~3.6V. It is operating at a temperature of -40°C~85°C TA. It is an electronic flip flop with the type D-Type. The 74LVTHseries comprises this type of FPGA. A frequency of 150MHzshould not be exceeded by its output. D latch consists of 1 elements. It consumes 190μA of quiescent current without being affected by external factors. JK flip flop belongs to 74LVTH273 family. This JK flip flop has a 3pFfarad input capacitance. A part of the electronic system is mounted in the way of Surface Mount. The electronic flip flop is designed with pins 20. There is a clock edge trigger type of Positive Edgeon this device. The flip flop is designed with 8bits. In order to achieve its superior flexibility, 8 circuits are used. For high efficiency, the supply voltage should be kept at 3.3V. To operate, the chip has a total of 7 output lines. A total of 4input lines have been provided. A high level output current of -32mAis set. There is no low level output current set at 64mA. Operating temperatures should be lower than 85°C. Temperatures above -40°Cshould be used. Initially, it requires a voltage of 2.7V as the minimum supply voltage. 3.6Vis the maximum supply voltage supported by it. It is possible to achieve 150MHz frequencies.
74LVTH273SJX Features
Tape & Reel (TR) package
74LVTH series
20 pins
8 Bits
74LVTH273SJX Applications
There are a lot of ON Semiconductor 74LVTH273SJX Flip Flops applications.
- Modulo – n – counter
- Guaranteed simultaneous switching noise level
- 2 – Bit synchronous counter
- Load Control
- Reduced system switching noise
- Single Down Count-Control Line
- Digital electronics systems
- Buffer registers
- Balanced 24 mA output drivers
- Set-reset capability