74LVTH162374GRDR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 54-TFBGA |
| Number of Pins | 54 |
| Weight | 99.705273mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74LVTH |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 54 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | BICMOS |
| Voltage - Supply | 2.7V~3.6V |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Supply Voltage | 3.3V |
| Base Part Number | 74LVTH162374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 3.3V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 3.6V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 12mA |
| Number of Bits | 8 |
| Clock Frequency | 160MHz |
| Propagation Delay | 3.4 ns |
| Turn On Delay Time | 3.4 ns |
| Family | LVT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 190μA |
| Output Characteristics | 3-STATE WITH SERIES RESISTOR |
| Current - Output High, Low | 12mA 12mA |
| Max Propagation Delay @ V, Max CL | 5.3ns @ 3.3V, 50pF |
| Prop. Delay@Nom-Sup | 5.3 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 160000000Hz |
| Width | 5.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
74LVTH162374GRDR Overview
The flip flop is packaged in a case of 54-TFBGA. D flip flop is embedded in the Cut Tape (CT) package. In the configuration, Tri-State, Non-Invertedis used as the output. This trigger uses the value Positive Edge. Surface Mountis occupied by this electronic component. A supply voltage of 2.7V~3.6V is required for operation. -40°C~85°C TAis the operating temperature. D-Typedescribes this flip flop. In FPGA terms, D flip flop is a type of 74LVTHseries FPGA. You should not exceed 160MHzin its output frequency. In total, it contains 2 elements. There is a consumption of 190μAof quiescent energy. It has been determined that there have been 54 terminations. This D latch belongs to the family of 74LVTH162374. A voltage of 3.3V is used to power it. A 3pFfarad input capacitance is provided by this T flip flop. It is a member of the LVTfamily of D flip flop. Surface Mount mounts this electronic component. The 54pins are designed into the board. The clock edge trigger type for this device is Positive Edge. It is part of the FF/Latchesbase part number family. It is designed with 8bits. There is a 3.6Vmaximum supply voltage (Vsup). In view of its reliability, this D flip flop is a good fit for TAPE AND REEL. A total of 2ports are embedded in the D flip flop. Optimal efficiency requires a supply voltage of 3.3V. The output current of 12mA makes it feature maximum design flexibility. The number of input lines is 8.
74LVTH162374GRDR Features
Cut Tape (CT) package
74LVTH series
54 pins
8 Bits
74LVTH162374GRDR Applications
There are a lot of Texas Instruments 74LVTH162374GRDR Flip Flops applications.
- ESD protection
- Patented noise
- Storage registers
- Bounce elimination switch
- Dynamic threshold performance
- Set-reset capability
- Common Clocks
- Memory
- Load Control
- EMI reduction circuitry