74LVC2G66GD,125
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-XFDFN |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 15Ohm |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74LVC2G66 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 200μA |
| Nominal Supply Current | 100nA |
| Power Dissipation | 250mW |
| Max Supply Current | 200μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 4.6 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 3.8 ns |
| -3db Bandwidth | 500MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 46 dB |
| Current - Leakage (IS(off)) (Max) | 5μA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 3.9ns, 5ns |
| Charge Injection | 7.5pC |
| Crosstalk | -56dB @ 1MHz |
| Switch-on Time-Max | 13ns |
| Switch-off Time-Max | 11.5ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NO |
| Height Seated (Max) | 0.5mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74LVC2G66GD,125 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-XFDFN. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have the same number of circuits 1:1. Operating temperature extended to -40°C~125°C TA. A total of 8 terminations have been recorded. This electronic part offers high-quality output due to its 1 channels. It is safe to turn on and run the electronic component with a 2.7V voltage supply. Into the electrical component body are injected 8 pins. SPST - NO switching circuits are used in these analog switch ics. Try searching with 74LVC2G66 to find analog multiplexer variants. Internally, this switch multiplexer has a resistance of 15Ohm. To find out what the 8 pins do, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. An effective Single supply digital multiplexer. It is recommended that the electrical component receives a voltage of 1.65V. For this digital switch to work, 200μA current would suffice. Analogue multiplexers require a 1.65V~5.5V voltage to drain from a single voltage supply. Putting voltage greater than 200μA on the multiplexer may cause damage. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. There is a voltage range of 5V operating voltages for the electrical part. Operating 2 inputs is required.
74LVC2G66GD,125 Features
1 Channels
Switch Circuit: SPST - NO
200μA Supply Current
-3db Bandwidth: 500MHz
74LVC2G66GD,125 Applications
There are a lot of Nexperia USA Inc. 74LVC2G66GD,125 Analog Switches & Multiplexers ICs applications.
- Microprocessor controlled systems
- Low-Voltage
- Routers
- Intelligent PBX
- Video switching
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- E1 Network Equipment
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Optical Applications
- Signal routing between systems