74HCT574PW-Q100,11
| Parameters | |
|---|---|
| Factory Lead Time | 4 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-TSSOP |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2014 |
| Series | 74HCT |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 69MHz |
| Base Part Number | 74HCT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 8 |
| Clock Frequency | 76MHz |
| Propagation Delay | 50 ns |
| Turn On Delay Time | 18 ns |
| Logic Function | D-Type |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 6mA 6mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 33ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | 6mA |
| Input Capacitance | 3.5pF |
| Low Level Output Current | 6mA |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | ROHS3 Compliant |
74HCT574PW-Q100,11 Overview
The flip flop is packaged in 20-TSSOP (0.173, 4.40mm Width). D flip flop is embedded in the Tape & Reel (TR) package. Tri-State, Non-Invertedis the output configured for it. It is configured with a trigger that uses Positive Edge. In this case, the electronic component is mounted in the way of Surface Mount. The JK flip flop operates at 4.5V~5.5Vvolts. In the operating environment, the temperature is -40°C~125°C TA. This D latch has the type D-Type. This type of FPGA is a part of the 74HCT series. You should not exceed 76MHzin the output frequency of the device. In total, it contains 1 elements. As a result, it consumes 8μA of quiescent current without being affected by external factors. The 74HCT574 family contains it. A JK flip flop with a 3.5pFfarad input capacitance is used here. This electronic part is mounted in the way of Surface Mount. There are 20pins on it. It has a clock edge trigger type of Positive Edge. There are 8bits in its design. Optimal efficiency requires a supply voltage of 5V. It is set to 6mAfor the high level output current. There is no low level output current set at 6mA. A temperature below 125°Cshould be used for operation. It should be higher than -40°Cwhen the system is operating. A minimum supply voltage of 4.5V is required for these RS flip flops to operate. A maximum voltage of 5.5V can be provided by it. The frequency that can be achieved is 69MHz.
74HCT574PW-Q100,11 Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
74HCT574PW-Q100,11 Applications
There are a lot of Nexperia USA Inc. 74HCT574PW-Q100,11 Flip Flops applications.
- Data storage
- ESCC
- Shift Registers
- Shift registers
- Parallel data storage
- Storage registers
- Single Down Count-Control Line
- Latch
- Power down protection
- Latch-up performance