74HCT273DB,118
| Parameters | |
|---|---|
| Factory Lead Time | 13 Weeks |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74HCT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 36MHz |
| Propagation Delay | 15 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 15 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 4mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 30ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2mm |
| Length | 7.2mm |
| Width | 5.3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HCT273DB,118 Overview
20-SSOP (0.209, 5.30mm Width)is the way it is packaged. It is contained within the Tape & Reel (TR)package. Non-Invertedis the output configured for it. It is configured with a trigger that uses a value of Positive Edge. This electronic part is mounted in the way of Surface Mount. The JK flip flop operates at 4.5V~5.5Vvolts. It is operating at a temperature of -40°C~125°C TA. This logic flip flop is classified as type D-Type. The 74HCTseries comprises this type of FPGA. There should be no greater frequency than 36MHzon its output. In total, it contains 1 elements. There are 20 terminations,It is a member of the 74HCT273 family. It is powered from a supply voltage of 5V. The input capacitance of this T flip flop is 3.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. In this case, the D flip flop belongs to the HCTfamily. There is an electronic part mounted in the way of Surface Mount. With its 20pins, it is designed to work with most electronic flip flops. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This flip flop is designed with 8 Bits. For high efficiency, the supply voltage should be set to 5V. It has 8lines. It consumes 8μA of quiescent current without being affected by external factors.
74HCT273DB,118 Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
74HCT273DB,118 Applications
There are a lot of Nexperia USA Inc. 74HCT273DB,118 Flip Flops applications.
- Automotive
- Circuit Design
- Storage Registers
- Balanced Propagation Delays
- Latch
- Bounce elimination switch
- Modulo – n – counter
- Load Control
- Matched Rise and Fall
- Asynchronous counter