74HC273PW-Q100J
| Parameters | |
|---|---|
| Factory Lead Time | 4 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| Series | 74HC |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HC273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Number of Bits | 8 |
| Clock Frequency | 122MHz |
| Propagation Delay | 26 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 15 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 26ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| fmax-Min | 24 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HC273PW-Q100J Overview
In the form of 20-TSSOP (0.173, 4.40mm Width), it has been packaged. It is contained within the Tape & Reel (TR)package. Currently, the output is configured to use Non-Inverted. The trigger configured with it uses Positive Edge. Surface Mountmounts this electrical part. The JK flip flop operates at a voltage of 2V~6V. A temperature of -40°C~125°C TAis considered to be the operating temperature. It is an electronic flip flop with the type D-Type. It belongs to the 74HCseries of FPGAs. Its output frequency should not exceed 122MHz Hz. A total of 1 elements are present. It has been determined that there have been 20 terminations. D latch belongs to the 74HC273 family. It is powered from a supply voltage of 5V. Input capacitance of this device is 3.5pF farads. A device of this type belongs to the family of HC/UH. It is mounted in the way of Surface Mount. 20pins are included in its design. The clock edge trigger type for this device is Positive Edge. This flip flop is designed with 8 Bits. It reaches the maximum supply voltage (Vsup) at 6V. Normal operation requires a supply voltage (Vsup) above 2V. The superior flexibility of this product is achieved by using 8 circuits. In order to ensure high efficiency, the supply voltage should remain at 5V. 8μAquiescent current consumed.
74HC273PW-Q100J Features
Tape & Reel (TR) package
74HC series
20 pins
8 Bits
74HC273PW-Q100J Applications
There are a lot of Nexperia USA Inc. 74HC273PW-Q100J Flip Flops applications.
- Balanced Propagation Delays
- CMOS Process
- Instrumentation
- ESD performance
- Divide a clock signal by 2 or 4
- Set-reset capability
- Registers
- Circuit Design
- QML qualified product
- Frequency Divider circuits