74FCT574CTSOG8
| Parameters | |
|---|---|
| Factory Lead Time | 7 Weeks |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | BROADSIDE VERSION OF 374 |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.25V |
| Min Supply Voltage | 4.75V |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Propagation Delay | 5.2 ns |
| Quiescent Current | 1mA |
| Turn On Delay Time | 5.5 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| High Level Output Current | -15mA |
| Low Level Output Current | 15mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 6pF |
| Length | 12.8mm |
| Width | 7.6mm |
| Thickness | 2.34mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT574CTSOG8 Overview
As a result, it is packaged as SOIC. D flip flop is included in the Tape & Reel (TR)package. In total, there are 1 elements. It has been determined that there have been 20 terminations. A voltage of 5V is used to power it. An electronic device belonging to the family FCTcan be found here. Surface Mount mounts this electronic component. A total of 20pins are provided on this board. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The RS flip flops belongs to FF/Latches base part number. There are 8bits in its design. Considering its reliability, this T flip flop is well suited for TAPE AND REEL. A power supply of 5Vis required to operate it. The flip flop contains 2ports. If high efficiency is desired, the supply voltage should be kept at 5V. In terms of quiescent current, it consumes 1mA . In addition, BROADSIDE VERSION OF 374is a characteristic of it. A -15mAis set for the high level output current. Low level output current is set to 15mA. Ideally, the operating temperature should be below 85°C. If the operating temperature is higher than -40°C, the system should operate properly. The system operates with a minimum supply voltage of 4.75V. 5.25Vis the maximum supply voltage it supports. There is a logic IC BUS DRIVER used in the D flip flop. The T flip flop is equipped with 1functions . A total of 20 pins are present on this device.
74FCT574CTSOG8 Features
Tape & Reel (TR) package
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
74FCT574CTSOG8 Applications
There are a lot of Integrated Device Technology (IDT) 74FCT574CTSOG8 Flip Flops applications.
- Cold spare funcion
- Frequency Dividers
- Consumer
- Buffered Clock
- 2 – Bit synchronous counter
- Guaranteed simultaneous switching noise level
- ATE
- Reduced system switching noise
- Asynchronous counter
- Clock pulse