74FCT377CTQG8
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | SSOP |
| Number of Pins | 20 |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | WITH HOLD MODE |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.25V |
| Min Supply Voltage | 4.75V |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Propagation Delay | 5.2 ns |
| Quiescent Current | 1mA |
| Turn On Delay Time | 5.2 ns |
| Family | FCT |
| Logic Function | AND, D-Type |
| Output Characteristics | 3-STATE |
| Logic IC Type | D FLIP-FLOP |
| High Level Output Current | -15mA |
| Low Level Output Current | 12mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 6pF |
| Length | 8.7mm |
| Width | 3.8mm |
| Thickness | 1.47mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT377CTQG8 Overview
As a result, it is packaged as SSOP. Package Tape & Reel (TR)embeds it. A total of 1 elements are present. Terminations are 20. It is powered from a supply voltage of 5V. FCTis the family of this D flip flop. In this case, the electronic component is mounted in the way of Surface Mount. The electronic flip flop is designed with pins 20. This device exhibits a clock edge trigger type of Positive Edge. The RS flip flops belongs to FF/Latches base part number. There are 8bits in its design. In view of its reliability, this D flip flop is a good fit for TAPE AND REEL. A total of 5V power supplies are needed to run it. The supply voltage should be maintained at 5V for high efficiency. This D latch consumes 1mA quiescent current at all. Additionally, you may refer to the D latch's additional WITH HOLD MODE. -15mAis the output current at high level. It is set to 12mAfor low level output current. Operating temperatures should be lower than 85°C. Temperatures above -40°Cshould be used. The system operates with a minimum supply voltage of 4.75V. 5.25Vis the maximum supply voltage supported by it. It uses a logic IC with a D FLIP-FLOP value. It has 1 functions. The JK flip flop has a pin count of 20.
74FCT377CTQG8 Features
Tape & Reel (TR) package
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
74FCT377CTQG8 Applications
There are a lot of Integrated Device Technology (IDT) 74FCT377CTQG8 Flip Flops applications.
- Convert a momentary switch to a toggle switch
- Control circuits
- Safety Clamp
- ATE
- Reduced system switching noise
- Cold spare funcion
- CMOS Process
- Supports Live Insertion
- Latch
- Circuit Design