74FCT162374ATPVG8
| Parameters | |
|---|---|
| Factory Lead Time | 7 Weeks |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | SSOP |
| Number of Pins | 48 |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 48 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 48 |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 16 |
| Propagation Delay | 6.5 ns |
| Quiescent Current | 500μA |
| Turn On Delay Time | 6.5 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE WITH SERIES RESISTOR |
| Logic IC Type | BUS DRIVER |
| Number of Bits per Element | 8 |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 3.5pF |
| Length | 15.9mm |
| Width | 7.5mm |
| Thickness | 2.3mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT162374ATPVG8 Overview
It is packaged in the way of SSOP. A total of 2elements are present in it. It has been determined that there have been 48 terminations. A voltage of 5V is used as the power supply for this D latch. It is a member of the FCTfamily of D flip flop. In this case, the electronic component is mounted in the way of Surface Mount. The electronic flip flop is designed with pins 48. The clock edge trigger type for this device is Positive Edge. The part is included in FF/Latches. 16bits are used in its design. Compared to other similar T flip flops, this device offers reliable performance and is well suited for TAPE AND REEL. The system runs on a power supply of 5V watts. There are 2 ports embedded in the flip flops. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. 500μAquiescent current consumed. A high level output current of -24mAis set. A 24mAvalue is set for low-level output current. A temperature below 85°Cis recommended for operation. Ideally, the operating temperature should be higher than -40°C. In order for it to operate, a supply voltage of 4.5Vis required. There is a maximum voltage support of 5.5V. In this case, it uses a BUS DRIVER logic IC. A total of 2 functions are provided by this T flip flop. The D latch is equipped with 48 pins.
74FCT162374ATPVG8 Features
48 pins
16 Bits
5V power supplies
2 Functions
48 pin count
74FCT162374ATPVG8 Applications
There are a lot of Integrated Device Technology (IDT) 74FCT162374ATPVG8 Flip Flops applications.
- Divide a clock signal by 2 or 4
- Set-reset capability
- Shift registers
- Shift Registers
- Asynchronous counter
- Supports Live Insertion
- Modulo – n – counter
- Bus hold
- Single Up Count-Control Line
- Functionally equivalent to the MC10/100EL29