74F564PC
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Supplier Device Package | 20-PDIP |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74F |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 100MHz |
| Base Part Number | 74F564 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 8 |
| Clock Frequency | 100MHz |
| Propagation Delay | 8.5 ns |
| Turn On Delay Time | 5.2 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 86mA |
| Current - Output High, Low | 3mA 24mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 8.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -3mA |
| Low Level Output Current | 24mA |
| Number of Input Lines | 1 |
| Number of Output Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74F564PC Overview
The flip flop is packaged in a case of 20-DIP (0.300, 7.62mm). There is an embedded version in the package Tube. This output is configured with Tri-State, Non-Inverted. The trigger it is configured with uses Positive Edge. Through Holeis occupied by this electronic component. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. A temperature of 0°C~70°C TAis considered to be the operating temperature. This D latch has the type D-Type. It belongs to the 74Fseries of FPGAs. A frequency of 100MHzshould be the maximum output frequency. There are 1 elements in it. It consumes 86mA of quiescent You can search similar parts based on 74F564. A part of the electronic system is mounted in the way of Through Hole. A total of 20pins are provided on this board. There is a clock edge trigger type of Positive Edgeon this device. An electronic part with 8bits has been designed. Despite its superior flexibility, it relies on 8 circuits to achieve it. The supply voltage should be maintained at 5V for high efficiency. In order to operate, the chip has 8 output lines. There are 1 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. It is set to -3mAfor the high level output current. The low level output current is set to 24mA. A temperature below 70°Cshould be used for operation. If the operating temperature is higher than 0°C, the system should operate properly. A minimum supply voltage of 4.5V is required for these RS flip flops to operate. 5.5Vis its maximum supply voltage. A frequency of 100MHzcan be achieved.
74F564PC Features
Tube package
74F series
20 pins
8 Bits
74F564PC Applications
There are a lot of ON Semiconductor 74F564PC Flip Flops applications.
- Bus hold
- Asynchronous counter
- Clock pulse
- Guaranteed simultaneous switching noise level
- Balanced Propagation Delays
- Data Synchronizers
- Load Control
- CMOS Process
- Automotive
- Divide a clock signal by 2 or 4