74ACT534SCX
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-SOIC |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74ACT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 100MHz |
| Base Part Number | 74ACT534 |
| Function | Standard |
| Output Type | Tri-State, Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 8 |
| Clock Frequency | 100MHz |
| Propagation Delay | 11.5 ns |
| Turn On Delay Time | 6.5 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 40μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 11.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 8 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74ACT534SCX Overview
20-SOIC (0.295, 7.50mm Width)is the packaging method. It is contained within the Tape & Reel (TR)package. T flip flop is configured with an output of Tri-State, Inverted. It is configured with a trigger that uses a value of Positive Edge. There is an electronic component mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis required for its operation. Temperature is set to -40°C~85°C TA. It belongs to the type D-Typeof flip flops. In terms of FPGAs, it belongs to the 74ACT series. A frequency of 100MHzshould not be exceeded by its output. A total of 1elements are contained within it. T flip flop consumes 40μA quiescent energy. If you search by 74ACT534, you will find similar parts. This JK flip flop has a 4.5pFfarad input capacitance. There is an electronic part mounted in the way of Surface Mount. A total of 20pins are provided on this board. This device has Positive Edgeas its clock edge trigger type. 8bits are used in its design. Its flexibility is enhanced by 8 circuits. For high efficiency, the supply voltage should be set to 5V. In order to operate, the chip has 3 output lines. The number of input lines is 8. The high level output current is set to -24mA. 24mAis set as the low level output current. There should be a temperature below 85°Cduring operation. In order for the system to operate properly, the temperature should be higher than -40°C. The system operates with a minimum supply voltage of 4.5V. The maximum supply voltage supported by the flip flop is 5.5V. It is possible to achieve 100MHz frequencies.
74ACT534SCX Features
Tape & Reel (TR) package
74ACT series
20 pins
8 Bits
74ACT534SCX Applications
There are a lot of ON Semiconductor 74ACT534SCX Flip Flops applications.
- Circuit Design
- Communications
- Reduced system switching noise
- Frequency division
- Digital electronics systems
- Buffered Clock
- Modulo – n – counter
- Synchronous counter
- ESCC
- Supports Live Insertion