74ACQ574SC
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-SOIC |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74ACQ |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 2V~6V |
| Frequency | 90MHz |
| Base Part Number | 74ACQ574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Number of Bits | 8 |
| Clock Frequency | 90MHz |
| Propagation Delay | 13 ns |
| Turn On Delay Time | 6.5 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 40μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 8.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 1 |
| Number of Output Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74ACQ574SC Overview
20-SOIC (0.295, 7.50mm Width)is the way it is packaged. D flip flop is included in the Tubepackage. Tri-State, Non-Invertedis the output configured for it. Positive Edgeis the trigger it is configured with. This electronic part is mounted in the way of Surface Mount. The supply voltage is set to 2V~6V. A temperature of -40°C~85°C TAis considered to be the operating temperature. This logic flip flop is classified as type D-Type. In this case, it is a type of FPGA belonging to the 74ACQ series. It should not exceed 90MHzin terms of its output frequency. In total, it contains 1 elements. It consumes 40μA of quiescent If you search by 74ACQ574, you will find similar parts. Input capacitance of this device is 4.5pF farads. In this case, the electronic component is mounted in the way of Surface Mount. As you can see from the design, it has pins with 20. A Positive Edgeclock edge trigger is used in this device. There are 8bits in its design. Despite its superior flexibility, it relies on 8 circuits to achieve it. In order to operate, the chip has 8 output lines. There are 1 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. A -24mAis set for the high level output current. There is 24mA output current at the low level. Operating temperatures should be lower than 85°C. Ideally, the operating temperature should be greater than -40°C. A minimum supply voltage of 2V is required for these RS flip flops to operate. There is a maximum supply voltage of 6V. It is possible to obtain a frequency of 90MHz.
74ACQ574SC Features
Tube package
74ACQ series
20 pins
8 Bits
74ACQ574SC Applications
There are a lot of ON Semiconductor 74ACQ574SC Flip Flops applications.
- Safety Clamp
- Modulo – n – counter
- Pattern generators
- Automotive
- Consumer
- Common Clocks
- Single Down Count-Control Line
- Frequency division
- Storage registers
- ATE