74AC377SCX
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-SOIC |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AC |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 2V~6V |
| Frequency | 175MHz |
| Base Part Number | 74AC377 |
| Function | Standard |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Number of Bits | 8 |
| Clock Frequency | 175MHz |
| Propagation Delay | 13 ns |
| Turn On Delay Time | 6 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 40μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 9ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -24mA |
| Input Capacitance | 4.5pF |
| Low Level Output Current | 24mA |
| Number of Input Lines | 1 |
| Number of Output Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74AC377SCX Overview
It is embeded in 20-SOIC (0.295, 7.50mm Width) case. D flip flop is embedded in the Tape & Reel (TR) package. T flip flop is configured with an output of Non-Inverted. This trigger uses the value Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 2V~6V volts. It is at -40°C~85°C TAdegrees Celsius that the system is operating. It belongs to the type D-Typeof flip flops. In FPGA terms, D flip flop is a type of 74ACseries FPGA. Its output frequency should not exceed 175MHz. In total, it contains 1 elements. T flip flop consumes 40μA quiescent energy. It is a member of the 74AC377 family. The input capacitance of this T flip flop is 4.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. This electronic part is mounted in the way of Surface Mount. This board has 20 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. There are 8bits in this flip flop. Using 8 circuits, it is highly flexible. There are no output lines on the JK flip flop. The number of input lines is 1. -24mAis the output current at high level. It is set to 24mAfor low level output current. It is recommended that the operating temperature be below 85°C. Ideally, the operating temperature should be higher than -40°C. Normally, it operates with a voltage of 2VV as its minimum supply voltage. A maximum voltage of 6V can be provided by it. It is possible to obtain a frequency of 175MHz.
74AC377SCX Features
Tape & Reel (TR) package
74AC series
20 pins
8 Bits
74AC377SCX Applications
There are a lot of ON Semiconductor 74AC377SCX Flip Flops applications.
- Communications
- Shift Registers
- Pattern generators
- Reduced system switching noise
- Buffered Clock
- Differential Individual
- High Performance Logic for test systems
- Data transfer
- Data Synchronizers
- Balanced 24 mA output drivers