74ABT273CMTCX
| Parameters | |
|---|---|
| Series | 74ABT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 200MHz |
| Base Part Number | 74ABT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 8 |
| Clock Frequency | 200MHz |
| Propagation Delay | 6.8 ns |
| Turn On Delay Time | 6 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 50μA |
| Current - Output High, Low | 32mA 64mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 6.8ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -32mA |
| Input Capacitance | 5pF |
| Low Level Output Current | 64mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Supplier Device Package | 20-TSSOP |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
74ABT273CMTCX Overview
The flip flop is packaged in 20-TSSOP (0.173, 4.40mm Width). D flip flop is included in the Tape & Reel (TR)package. This output is configured with Non-Inverted. It is configured with a trigger that uses Positive Edge. There is an electronic component mounted in the way of Surface Mount. With a supply voltage of 4.5V~5.5V volts, it operates. It is operating at -40°C~85°C TA. This electronic flip flop is of type D-Type. The 74ABTseries comprises this type of FPGA. There should be no greater frequency than 200MHzon its output. A total of 1elements are present in it. There is 50μA quiescent consumption. The 74ABT273 family contains it. A JK flip flop with a 5pFfarad input capacitance is used here. The electronic part is mounted in the way of Surface Mount. This board is designed with 20pins on it. This device exhibits a clock edge trigger type of Positive Edge. The design is based on 8bits. Its flexibility is enhanced by 8 circuits. Optimal efficiency requires a supply voltage of 5V. The JK flip flop is with 8 output lines to operate. The number of input lines is 3. -32mAis the output current at high level. 64mA is the low level output current. It is recommended that the operating temperature be lower than 85°C. If the operating temperature is higher than -40°C, the system should operate properly. In order for it to operate, a supply voltage of 4.5Vis required. It supports the maximal supply voltage of 5.5V. It is possible to achieve a frequency of 200MHz.
74ABT273CMTCX Features
Tape & Reel (TR) package
74ABT series
20 pins
8 Bits
74ABT273CMTCX Applications
There are a lot of ON Semiconductor 74ABT273CMTCX Flip Flops applications.
- Patented noise
- Divide a clock signal by 2 or 4
- Convert a momentary switch to a toggle switch
- Counters
- Frequency Dividers
- Automotive
- Buffer registers
- Individual Asynchronous Resets
- Data transfer
- Common Clocks