SN74ACT574DBR
| Parameters | |
|---|---|
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 110MHz |
| Propagation Delay | 11 ns |
| Turn On Delay Time | 7 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height | 2mm |
| Length | 7.2mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 156.687814mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74ACT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
SN74ACT574DBR Overview
The flip flop is packaged in a case of 20-SSOP (0.209, 5.30mm Width). A package named Cut Tape (CT)includes it. T flip flop is configured with an output of Tri-State, Non-Inverted. The trigger it is configured with uses Positive Edge. The electronic part is mounted in the way of Surface Mount. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. Temperature is set to -40°C~85°C TA. It belongs to the type D-Typeof flip flops. It belongs to the 74ACTseries of FPGAs. A frequency of 110MHzshould be the maximum output frequency. In total, there are 1 elements. It consumes 4μA of quiescent current without being affected by external factors. A total of 20 terminations have been made. It is a member of the 74ACT574 family. A voltage of 5V is used as the power supply for this D latch. A 4.5pFfarad input capacitance is provided by this T flip flop. In this case, the D flip flop belongs to the ACTfamily. The electronic part is mounted in the way of Surface Mount. It is designed with 20 pins. A Positive Edgeclock edge trigger is used in this device. This device is part of the FF/Latchesbase part number family. There are 8bits in its design. Due to its superior flexibility, it uses 8 circuits. As a result of its reliability, this D flip flop is ideally suited for TR. The D latch operates on 5V volts. There are 2 ports embedded in the flip flops. In order to achieve high efficiency, the supply voltage should be maintained at 5V. This T flip flop features a maximum design flexibility due to its output current of 24mA. Currently, there are 3 lines of input.
SN74ACT574DBR Features
Cut Tape (CT) package
74ACT series
20 pins
8 Bits
5V power supplies
SN74ACT574DBR Applications
There are a lot of Texas Instruments SN74ACT574DBR Flip Flops applications.
- Asynchronous counter
- Cold spare funcion
- Common Clocks
- Data transfer
- Synchronous counter
- Bus hold
- Circuit Design
- Divide a clock signal by 2 or 4
- Single Down Count-Control Line
- ESD performance