MAX4748ETE+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WQFN Exposed Pad |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 50Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | QUAD |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.8mm |
| Base Part Number | MAX4748 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 11V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Throw Configuration | SPST |
| Supply Type | Single |
| -3db Bandwidth | 250MHz |
| On-State Resistance (Max) | 25Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 20pF 20pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 85ns, 45ns |
| Charge Injection | 9pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -84dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 150ns |
| Switch-off Time-Max | 60ns |
| Voltage - Supply, Single (V+) | 2V~11V |
| Normal Position | NC |
| Height Seated (Max) | 0.8mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4748ETE+T Overview
Presented in 16-WQFN Exposed Pad, this electrical component is convenient for overseas shipping. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. 16 terminations have been made so far. A high-quality output is provided by the electrical component's 1 channels. An 3V voltage supply should allow the electrical part to be turned on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. A SPST - NC switching circuit is used to build these analog multiplexers. Circuits number 4 make up this analogue multiplexer. Try searching for the analog switch ic with MAX4748 if you are looking for variants. A 50Ohm internal resistance characterizes this multiplexer. To find out what the 16 pins do, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 11V. Analogue multiplexer with a Single supply type that is cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. An operating current of 1μA would be sufficient for this switch device. Analogue multiplexers require a 2V~11V voltage to drain from a single voltage supply. There are SEPARATE OUTPUT outputs on this analog switch ic.
MAX4748ETE+T Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
-3db Bandwidth: 250MHz
MAX4748ETE+T Applications
There are a lot of Maxim Integrated MAX4748ETE+T Analog Switches & Multiplexers ICs applications.
- ATM
- PDAs
- Precision data acquisition
- Cable Modem
- Automotive applications
- 65 V DACs
- Medical Instrumentation
- HDTV
- Switching Systems
- Optical Applications