MAX4652ESE+T
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4652 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 10 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 16 ns |
| On-State Resistance (Max) | 4Ohm |
| High Level Output Current | 50mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 16pF 16pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 14ns, 8ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4652ESE+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. It is mounted in the position Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 16. A high-quality output is provided by the electrical component's 1 channels. A 3V voltage supply should turn on and run the electronic component. An electrical component like this is included in the 16 series. The analog switch ics are built using SPST - NO switching circuits. There are 4 circuits in this switch device. Search with MAX4652 if you are looking for analog multiplexer variants. The internal resistance of this digital multiplexer is 4Ohm. Multiplexer or Switches is a typical switch device. Users shouldn't supply more than 5.5V voltage to the switch device. Analogue multiplexers of the Single supply type that are cost-effective. It is recommended to use 1.8V as the lowest voltage for the electrical part. The analogue multiplexer could operate on 1μA current. Analogue multiplexers require a 1.8V~5.5V voltage to drain from a single voltage supply. Put voltage above 1μA on the multiplexer to cause damage. It can operate from 5V operating voltages.
MAX4652ESE+T Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX4652ESE+T Applications
There are a lot of Maxim Integrated MAX4652ESE+T Analog Switches & Multiplexers ICs applications.
- Central office
- Cell phones
- Medical Instrumentation
- Cellular phones
- Video signal routing
- RGB switches
- Frame Relay Equipment
- Avionics and Military Systems
- Communication systems
- Power routing