MAX4624EZT
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2001 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 6 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| On-State Resistance (Max) | 1Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 57 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 32pF |
| On-state Resistance Match-Nom | 0.06Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 50ns, 50ns |
| Charge Injection | 65pC |
| Channel-to-Channel Matching (ΔRon) | 60m Ω |
| Crosstalk | -57dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 50ns |
| Switch-off Time-Max | 50ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height | 900μm |
| Length | 3mm |
| Width | 1.65mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4624EZT Overview
Shipping overseas is convenient with the electronic component packed in SOT-23-6. High reliability is achieved by using advanced packaging method Tube. Multiplexers like this are mounted in the Surface Mount position. There is 2:1 ratio between the number of multiplexers and demultiplexers. The operating temperature is extended to around -40°C~85°C TA. In total, 6 terminations have occurred. By its 1 channels, the electronic component provides high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. As part of its design, the 6 series is equipped with this electronic component. Circuits based on SPDT switching are used to construct these analog switch ics. A 1 circuit is present in this switch device. Please refer to the datasheets for 6 pins functions. It is a typical Multiplexer or Switches analog multiplexer. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. A low voltage of 1.8V should be applied to the electronic component. Draining from a single voltage supply, this analog switch requires a voltage of 1.8V~5.5V. The electrical part can be operated at 5V voltage levels.
MAX4624EZT Features
1 Channels
Switch Circuit: SPDT
MAX4624EZT Applications
There are a lot of Maxim Integrated MAX4624EZT Analog Switches & Multiplexers ICs applications.
- Battery Powered Instruments
- Remote wireless modules
- PBX interfaces
- Data switching
- Industrial
- Video signal routing
- E1 Network Equipment
- Access Concentrators
- Battery Powered Systems
- SONET