MAX4515CUK-T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 10Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4515 |
| Pin Count | 5 |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 2μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 150 ns |
| On-State Resistance (Max) | 20Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 2pC |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NC |
| Length | 2.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4515CUK-T Overview
Presented in SC-74A, SOT-753, this electrical component is convenient for overseas shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, you'll find this switch device. 1:1 is the ratio between multiplexers and demultiplexers. Around 0°C~70°C TA is the extended operating temperature. There are 5 terminations totally. A high-quality output is provided by the electrical component's 1 channels. An 5V voltage supply should allow the electrical part to be turned on and run. Into the electrical component body are injected 5 pins. On the other hand, analog switches can be constructed using SPST - NC switching circuits. Search with MAX4515 if you are looking for analog multiplexer variants. Internally, this switch multiplexer has a resistance of 10Ohm. For details about the functions of 5 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users shouldn't supply more than 12V voltage to the switch device. The digital multiplexer has a low cost Single supply. 2V is the lowest voltage the electrical component should receive. 2μA current would be enough for this multiplexer to operate. A voltage of 2V~12V is required to drain this analog switch from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA.
MAX4515CUK-T Features
1 Channels
Switch Circuit: SPST - NC
2μA Supply Current
MAX4515CUK-T Applications
There are a lot of Maxim Integrated MAX4515CUK-T Analog Switches & Multiplexers ICs applications.
- Digital cross connects (DSX-1)
- Cable Modem
- Automotive applications
- Multiplexers
- Switching Systems
- Audio signal routing
- ATM
- DVD-R
- Industrial
- DSUs