MAX4501EUK-T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 250Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4501 |
| Pin Count | 5 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 500 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 175 ns |
| On-State Resistance (Max) | 250Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 100 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 3pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 1pC |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NO |
| Length | 2.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
MAX4501EUK-T Overview
Shipping overseas is convenient with the electronic component packed in SC-74A, SOT-753. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). It is mounted in the position Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -40°C~85°C TA extended. There are 5 terminations totally. As a result of its 1 channels, this electronic component provides high-quality output. With a 5V voltage supply, the electrical component should be turned on and run. An electrical component like this is included in the 5 series. Based on SPST - NO switching circuits, these analog multiplexers work. It consists of 1 circuits. Search with MAX4501 if you are looking for analog multiplexer variants. The internal resistance of this digital multiplexer is 250Ohm. You can find the functions of the 5 pins in the datasheets. Multiplexer or Switches is a typical switch device. A voltage higher than 5.5V should not normally be supplied to the switches. The analog switch ic is of the Single supply type and is cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. The switch device would be able to operate with 1μA current. A voltage of 2V~12V is required to drain this analog switch from a single voltage supply. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer.
MAX4501EUK-T Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX4501EUK-T Applications
There are a lot of Maxim Integrated MAX4501EUK-T Analog Switches & Multiplexers ICs applications.
- Sample-and-hold systems
- Automatic test equipment
- Precision data acquisition
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Cellular phones
- Power routing
- SONET
- Industrial and process control systems
- DSUs
- Precision instrumentation