MAX14689EWL+T
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Contact Plating | Copper, Silver, Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 9-WFBGA, WLBGA |
| Number of Pins | 9 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Series | Beyond-the-Rails™ |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 9 |
| Resistance | 450mOhm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 963.8mW |
| Technology | BICMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Terminal Pitch | 0.4mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX14689 |
| Output | SEPARATE OUTPUT |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 2.5V |
| Polarity | Non-Inverting |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.6V |
| Max Supply Current | 125μA |
| Turn On Delay Time | 200 μs |
| Supply Type | Single |
| Turn-Off Delay Time | 30 μs |
| -3db Bandwidth | 110MHz |
| On-State Resistance (Max) | 450mOhm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 25pF |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 200μs, 30μs |
| Channel-to-Channel Matching (ΔRon) | 5m Ω |
| Crosstalk | -100dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250000ns |
| Voltage - Supply, Single (V+) | 1.6V~5.5V |
| RoHS Status | ROHS3 Compliant |
MAX14689EWL+T Overview
Packed in 9-WFBGA, WLBGA, the electronic component is convenient for shipping overseas. High reliability is achieved by using advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. 2:2 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -40°C~85°C TA. Totally, there are 9 terminations. Based on DPDT switching circuits, these analog multiplexers work. 1 circuits are used in this analogue multiplexer. Try searching with MAX14689 if you're looking for variants. In this multiplexer, the internal resistance is 450mOhm. For details about the functions of 9 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 5.5V. A cost-effective Single supply type analogue multiplexer. 1.6V should be the lowest voltage fed to the electronic component. Draining from a single voltage supply, this analog switch requires a voltage of 1.6V~5.5V. A digital multiplexer may suffer damage if voltage is applied above 125μA. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. A voltage of 2.5V can be used to operate the electronic component. The Beyond-the-Rails? series is responsible for it.
MAX14689EWL+T Features
Switch Circuit: DPDT
-3db Bandwidth: 110MHz
MAX14689EWL+T Applications
There are a lot of Maxim Integrated MAX14689EWL+T Analog Switches & Multiplexers ICs applications.
- Signal routing between systems
- Microprocessor controlled systems
- Mechanical reed relay replacement
- Public switching systems
- Audio signal routing
- USB 1.1 signal switching circuits
- Transmit
- ISDN NT1/TA
- DSUs
- Private Branch Exchange (PBX)