ISL28130CHZ-T7A
| Parameters | |
|---|---|
| Factory Lead Time | 10 Weeks |
| Mount | Surface Mount |
| Package / Case | SOT-23 |
| Number of Pins | 5 |
| Published | 2005 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Operating Supply Voltage | 5V |
| Temperature Grade | COMMERCIAL |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 25μA |
| Slew Rate | 0.2 V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | OPERATIONAL AMPLIFIER |
| Common Mode Rejection Ratio | 125 dB |
| Current - Input Bias | 250pA |
| Output Current per Channel | 15mA |
| Supply Type | Dual, Single |
| Input Offset Voltage (Vos) | 5μV |
| Bandwidth | 400 kHz |
| Gain Bandwidth Product | 400 kHz |
| Unity Gain BW-Nom | 400 kHz |
| Voltage Gain | 150dB |
| Power Supply Rejection Ratio (PSRR) | 138dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Max Dual Supply Voltage | 2.75V |
| Low-Bias | YES |
| Micropower | YES |
| Min Dual Supply Voltage | 900mV |
| Programmable Power | NO |
| Length | 2.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
ISL28130CHZ-T7A Overview
The linear amplifier is packaged in a SOT-23 case. OPERATIONAL AMPLIFIER-type instrumentation amplifiers are used in this application. During the past two weeks, there have been close to 5 terminations. I would like to remind you that this buffer op amp should be powered by an 5V battery. Instrumentation amplifier is a part of Operational Amplifier. There are 5 pins on this chip. Op amp ic rates 5μV for input offset voltage. Using a supply current of 20μA , this buffer op amp will be able to operate. It is recommended to keep the voltage gain at 150dB at all times. On this instrumentation amplifier, there are 1 circuits that are connected together. In order for this buffer op amp to function, it should have a temperature of at least 0°C degrees Celsius. Instrumentation amplifier shouldn't be used above 70°C . The operating supply voltage of instrumentation amplifier is rated 5V voltage. This linear amplifier pack is based on the TAPE AND REEL axis. I would like to point out that this electrical component is capable of working from a voltage below 5.5V as far as the power supply is concerned. To keep the buffer amps' supply voltage higher than 1.8V. As a general rule, you should conduct this electronic component under dual supply voltages of 2.75V volts.
ISL28130CHZ-T7A Features
supply voltage of 5V
150dB voltage gain
ISL28130CHZ-T7A Applications
There are a lot of Intersil (Renesas Electronics America) ISL28130CHZ-T7A Instrumentational OP Amps applications.
- Logarithmic operation circuits
- Scintillation detectors
- Gaming industry
- Communication device
- Information processing
- Portable electronic products powered by batteries
- Measurements of Wheatstone bridge
- Medical instruments
- Polarized electrodes
- Commercial audio systems