DG9454EN-T1-E4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WFQFN |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2014 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 165Ohm |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Max Power Dissipation | 525mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.4mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG9454 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 2 |
| Number of Circuits | 3 |
| Max Supply Voltage | 13.2V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Power Dissipation | 525mW |
| Max Supply Current | 10μA |
| Propagation Delay | 170 ns |
| Turn On Delay Time | 250 ns |
| Logic Function | Multiplexer |
| Number of Inputs | 6 |
| Supply Type | Single |
| Bandwidth | 540MHz |
| Turn-Off Delay Time | 180 ns |
| On-State Resistance (Max) | 120Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 3pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 180ns, 110ns |
| Charge Injection | 0.86pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω |
| Crosstalk | -81dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~13.2V |
| Height | 800μm |
| Length | 2.6mm |
| Width | 1.8mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG9454EN-T1-E4 Overview
This electronic part is conveniently packaged in 16-WFQFN, making it easy to ship abroad. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. There is an analog multiplexer mounted in position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Extended operating temperature around -40°C~125°C TA. A total of 16 terminations have been recorded. This electronic part offers high-quality output due to its 2 channels. It is safe to turn on and run the electronic component with a 3V voltage supply. An electrical component of this type can be found in the 16 series. Based on SPDT switching circuits, these analog multiplexers work. This multiplexer is composed of 3 circuits. Try searching for the analog switch ic with DG9454 if you are looking for variants. Analog switches have 165Ohm internal resistance. The datasheets for the 16 pins explain the functions. A voltage higher than 13.2V should not normally be supplied to the switches. The analog switch ic is of the Single supply type and is cost-effective. 2.7V is the lowest voltage that should be fed to the electronic electronic part. In order to operate this switch device, it would need a current of 1μA. Using only a single voltage supply, this analog switch requires 2.7V~13.2V voltage. A voltage higher than 10μA may cause damage to the switch multiplexer. Operating 6 inputs is required. 540MHz bandwidths enable data to be transferred.
DG9454EN-T1-E4 Features
2 Channels
Switch Circuit: SPDT
1μA Supply Current
Bandwidth: 540MHz
DG9454EN-T1-E4 Applications
There are a lot of Vishay Siliconix DG9454EN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Cell phones
- Multiplexers
- Industrial and process control systems
- High reliability control systems
- Industrial
- Precision test equipment
- E1 Network Equipment
- SONET
- PDH Multiplexers
- Cable PC