DG9432DQ-T1-E3
| Parameters | |
|---|---|
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 77 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 7.5pF 7.8pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 35ns, 18ns |
| Charge Injection | 0.36pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -96dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 100ns |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | ROHS3 Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Number of Pins | 8 |
| Weight | 139.989945mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 60Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 320mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG9432 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Power Dissipation | 320mW |
| Max Supply Current | -1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 35 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 18 ns |
| On-State Resistance (Max) | 30Ohm |
DG9432DQ-T1-E3 Overview
Presented in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad, this electrical component is convenient for overseas shipping. High reliability is provided by advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. Total terminations are 8. A electrical component with 1 channels is capable of high-quality output. It is safe to turn on and run the electronic component with a 3V voltage supply. Electronic part bodies are injected with 8 pins. The analog switch ics are built using SPST - NC switching circuits. Try searching for DG9432 variants of the analog switch ic. Analog switches have 60Ohm internal resistance. For functions related to 8 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. normally, users should not supply switches with voltages higher than 12V. Single supply type digital switch with a low cost. 2.7V is the lowest voltage the electrical component should receive. 1μA current would be enough for this multiplexer to operate. A voltage of 2.7V~12V is required for this switch device, which drains from a single voltage source. Put voltage above -1μA on the multiplexer to cause damage. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. Operating the 2 inputs requires 2 inputs.
DG9432DQ-T1-E3 Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
DG9432DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG9432DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Automotive applications
- 65 V DACs
- CSU
- Access Concentrators
- Relay replacements
- Low-Voltage
- Modems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Battery Powered Instruments
- Sample hold systems