DG9411DL-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 14 Weeks |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Weight | 28.009329mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 12Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG9411 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.25V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Power Dissipation | 250mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 11 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 7 ns |
| On-State Resistance (Max) | 12Ohm |
| High Level Output Current | 50mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 73 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 7pF 20pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 11ns, 7ns |
| Charge Injection | 10pC |
| Crosstalk | -70dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 45ns |
| Voltage - Supply, Single (V+) | 2.25V~5.5V |
| Drain to Source Resistance | 12Ohm |
| Height | 1mm |
| Length | 2mm |
| Width | 1.25mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG9411DL-T1-E3 Overview
Due to its 6-TSSOP, SC-88, SOT-363 packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. 2:1 is the ratio between multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. Total terminations are 6. As a result of its 1 channels, this electronic component provides high-quality output. When a voltage supply of 2.5V is used, the electronic component should be turned on and run. Into the electrical component body are injected 6 pins. These analog multiplexers are built based on SPDT switching circuits. Try searching with DG9411 to find analog multiplexer variants. Analog switches have 12Ohm internal resistance. To find out what the 6 pins do, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. A analog switch ic that has a cost-effective Single supply type. 2.25V should be the lowest voltage fed to the electronic component. This multiplexer would work with 10nA current. Draining from a single voltage supply, this analog switch requires a voltage of 2.25V~5.5V. Putting voltage greater than 1μA on the multiplexer may cause damage. In order to operate the 1 inputs, there are several steps to follow. This electronic component presents a Drain to Source resistance of 12Ohm. The analog switch ics includes 2 outputs.
DG9411DL-T1-E3 Features
1 Channels
Switch Circuit: SPDT
10nA Supply Current
Drain-to-Source resistance: 12Ohm
DG9411DL-T1-E3 Applications
There are a lot of Vishay Siliconix DG9411DL-T1-E3 Analog Switches & Multiplexers ICs applications.
- 65 V DACs
- Central office
- Public switching systems
- Data Acquisition Systems
- Isolation
- Relay replacements
- Video switching
- Data switching
- Imaging
- Voice over IP/DSL – Integrated Access Devices, Smart