DG9263DY-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 60Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG9263 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 75 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 74 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG9263DY-E3 Overview
Due to its 8-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. This high-reliability packaging method uses advanced packaging methods Tube. This analog switch is mounted in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. The operating temperature is extended to around -40°C~85°C TA. In total, there have been 8 terminations. A high-quality output is provided by the electrical component's 1 channels. Turning on and running the electrical part should be easy with a 3V voltage supply. It is injected into the electrical part body with 8 pins. Based on SPST - NO switching circuits, these analog multiplexers work. Use DG9263 to search for variants of the digital switches. Internally, this switch multiplexer has a resistance of 60Ohm. Datasheets for 8 pin functions are available upon request. There is Multiplexer or Switches analog multiplexer like this in the world. In a normalsituation, users should not supply the switches with voltage higher than 12V. A cost-effective Single supply type analogue multiplexer. There should be 2.7V voltage fed to the electrical part below 2.7V. In order to operate this switch device, it would need a current of 1μA. A voltage of 2.7V~12V is required for this switch device, which drains from a single voltage source. The analogue multiplexer may be damaged if voltage is greater than 1μA. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. The 2 inputs need to be operated in order to work.
DG9263DY-E3 Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
DG9263DY-E3 Applications
There are a lot of Vishay Siliconix DG9263DY-E3 Analog Switches & Multiplexers ICs applications.
- Avionics and Military Systems
- 65 V DACs
- T1/E1 Terminals
- Cross Connects
- DSLAMs
- Private Branch Exchange (PBX)
- Central office
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Relay Replacement
- Medical