DG9233DY-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Termination | SMD/SMT |
| Resistance | 30Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG9233 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 75 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 30Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 74 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF 13pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG9233DY-T1-E3 Overview
Presented in 8-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. The advanced packaging method Tape & Reel (TR) provides high reliability. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Operating temperature around -40°C~85°C TA extended. There are 8 terminations totally. The electronic part delivers high-quality output through its 1 channels. When a voltage supply of 3V is used, the electronic component should be turned on and run. There is an electrical component included in the 8 series. Unlike digital switches, these are based on SPST - NO switching circuits. Try searching for DG9233 variants of the analog switch ic. There is 30Ohm internal resistance in this digital multiplexer. Please refer to the datasheets for 8 pins functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 12V. The analog switch ic is of the Single supply type and is cost-effective. 2.7V is the lowest voltage that should be fed to the electronic electronic part. The switch device would be able to operate with 1μA current. Draining from a single voltage supply, this analog switch requires a voltage of 2.7V~12V. A voltage higher than 1μA may cause damage to the switch multiplexer. There are SEPARATE OUTPUT outputs on this analog switch ic. The electrical component supports 2 inputs.
DG9233DY-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
DG9233DY-T1-E3 Applications
There are a lot of Vishay Siliconix DG9233DY-T1-E3 Analog Switches & Multiplexers ICs applications.
- Sample-and-hold systems
- Communications systems
- Ultrasound
- Digital access cross connects
- Medical systems
- Precision test equipment
- T1/E1 Terminals
- Audio and video switching
- DVD-R
- RGB switches