DG9233DY-T1
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 30Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 75 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 30Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 74 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF 13pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
DG9233DY-T1 Overview
Due to its 8-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. The operating temperature is extended to around -40°C~85°C TA. The total number of terminations is 8. Due to its 1 channels, the electrical component produces high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. A key feature of the 8 series is the inclusion of this electronic part as part of its design. A SPST - NO switching circuit is used for these analog switches. This digital multiplexer has 30Ohm internal resistance. You can find the functions of the 8 pins in the datasheets. This switch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 12V. Single supply type digital switch with a low cost. There should be 2.7V voltage fed to the electrical part below 2.7V. Using only a single voltage supply, this analog switch requires 2.7V~12V voltage. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. A 2 input needs to be operated.
DG9233DY-T1 Features
1 Channels
Switch Circuit: SPST - NO
DG9233DY-T1 Applications
There are a lot of Vishay Siliconix DG9233DY-T1 Analog Switches & Multiplexers ICs applications.
- Channelized and Unchannelized DS3 applications
- Remote Powered Equipment
- Audio and video routing
- SDH/SONET multiplexers
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Transmit
- CSU
- 65 V DACs
- USB 1.1 signal switching circuits
- Routers