DG787DQ-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 10 |
| Weight | 143.193441mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 2.9Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 320mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 2 |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | DG787 |
| Pin Count | 10 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Analog IC - Other Type | SPST |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 42 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 2.9Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 12pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 45ns, 42ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 250m Ω (Max) |
| Crosstalk | -56dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 51ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| RoHS Status | ROHS3 Compliant |
DG787DQ-T1-E3 Overview
The electronic component is convenient to ship overseas because it is packed in a 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. There is 2:1 ratio between the number of multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. In total, 10 terminations have occurred. The electrical component body receives 10 pins. A SPDT switching circuit is used for these analog switches. Circuits number 2 make up this analogue multiplexer. Try searching with DG787 if you're looking for variants. A 2.9Ohm internal resistance characterizes this multiplexer. For details about the functions of 10 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. A cost-effective Single supply type analogue multiplexer. It is recommended that the electrical component receives a voltage of 1.8V. 1μA current would be enough for this multiplexer to operate. A voltage of 1.8V~5.5V is required to drain this analog switch from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. It is integrated with SPST analog ICs.
DG787DQ-T1-E3 Features
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 300MHz
DG787DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG787DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Intelligent PBX
- PDH Multiplexers
- Digital cross connects (DSX-1)
- Microprocessor Controlled Analog Systems
- Frame Relay Equipment
- SDH/SONET multiplexers
- Microwave transmission systems
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Relay replacements
- Battery Powered Systems