DG722DN-T1-GE4
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-UFDFN Exposed Pad |
| Number of Pins | 8 |
| Weight | 50.008559mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 4.5Ohm |
| Additional Feature | VIDEO APPLICATION |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Max Supply Current | 2μA |
| Turn On Delay Time | 30 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 35 ns |
| -3db Bandwidth | 366MHz |
| On-State Resistance (Max) | 4.5Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 47 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 9pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 30ns, 35ns |
| Charge Injection | 2.2pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -90dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 55ns |
| Switch-off Time-Max | 40ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NC |
| Height | 550μm |
| Length | 2.05mm |
| Width | 2.05mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
DG722DN-T1-GE4 Overview
Due to its 8-UFDFN Exposed Pad packaging, the electronic part is convenient for international shipping. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Operational temperature extended around -40°C~85°C TA. There are 8 terminations totally. The electronic part provides high-quality output because it has 1 channels. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. An electrical component of this type can be found in the 8 series. Multiplexers built on a SPST - NC switching circuit are built. It consists of 2 circuits. This digital multiplexer has 4.5Ohm internal resistance. You can find the functions of the 8 pins in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Single supply type. 1.8V is the lowest voltage that should be fed to the electronic electronic part. Draining from a single voltage supply, this analog switch requires a voltage of 1.8V~5.5V. A voltage higher than 2μA may cause damage to the switch multiplexer. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. Additional features include: VIDEO APPLICATION.
DG722DN-T1-GE4 Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 366MHz
Additional Features: VIDEO APPLICATION
DG722DN-T1-GE4 Applications
There are a lot of Vishay Siliconix DG722DN-T1-GE4 Analog Switches & Multiplexers ICs applications.
- 65 V DACs
- Remote Powered Equipment
- Data Acquisition Systems
- Avionics test equipment
- Audio and video routing
- Digital access cross connects
- Frame Relay Equipment
- PDAs
- Automatic test equipment
- Private Branch Exchange (PBX)