DG418LDY-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 12 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 20Ohm |
| Terminal Finish | MATTE TIN |
| Additional Feature | VIDEO APPLICATION |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | BICMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG418 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 41 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 32 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 20Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 71 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 43ns, 31ns |
| Charge Injection | 1pC |
| Crosstalk | -71dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 44ns |
| Switch-off Time-Max | 33ns |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| RoHS Status | ROHS3 Compliant |
DG418LDY-T1-E3 Overview
Packed in 8-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 8. The electronic part provides high-quality output because it has 1 channels. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. Electronic part bodies are injected with 8 pins. SPST - NO switching circuits are used in these analog switch ics. Try searching for DG418 variants of the analog switch ic. Internally, this switch multiplexer has a resistance of 20Ohm. For functions related to 8 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. It is recommended that the electrical component receives a voltage of 2.7V. The switch device would be able to operate with 1μA current. Put voltage above 1μA on the multiplexer to cause damage. Despite this switch device's dual supply capability, its voltage should not exceed 6V. The voltage should be at least 3V if you are using dual power supplies. There are 1 inputs to be operated. Additional features of the electronic component include: VIDEO APPLICATION.
DG418LDY-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
Additional Features: VIDEO APPLICATION
DG418LDY-T1-E3 Applications
There are a lot of Vishay Siliconix DG418LDY-T1-E3 Analog Switches & Multiplexers ICs applications.
- Mechanical reed relay replacement
- SONET
- Video signal routing
- Modems
- Automotive applications
- Cellular phones
- Cable Modem
- Remote Powered Equipment
- Microprocessor Controlled Analog Systems
- SDH