DG408LDY-T1
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 547.485991mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 29Ohm |
| Terminal Finish | TIN LEAD |
| Additional Feature | VIDEO APPLICATION |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | BICMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Power Dissipation | 600mW |
| Max Supply Current | 500μA |
| Turn On Delay Time | 150 ns |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 29Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 7pF 20pF |
| Switch Time (Ton, Toff) (Max) | 55ns, 25ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -82dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 60ns |
| Switch-off Time-Max | 45ns |
| Signal Current-Max | 0.03A |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
DG408LDY-T1 Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a number of circuits 8:1. Operational temperature extended around -40°C~85°C TA. A total of 16 terminations have been recorded. High-quality output is provided by the electronic component's 8 channels. When the electronic component is given a voltage of 5V, it should be turned on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. A 1 circuit is present in this switch device. Internally, this switch multiplexer has a resistance of 29Ohm. The functions of 16 pins can be found in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 12V to the switch device in normal circumstances. Digital switch that provides Dual, Single power at a cost-effective price. 2.7V should be the lowest voltage fed to the electronic component. The analogue multiplexer may be damaged if voltage is greater than 500μA. For this switch, a dual supply voltage is feasible, but it must not exceed 6VThe voltage should be at least 3V if you are using dual power supplies. It is integrated with SINGLE-ENDED MULTIPLEXER analog ICs. Additional features of the electronic component include: VIDEO APPLICATION.
DG408LDY-T1 Features
8 Channels
Additional Features: VIDEO APPLICATION
DG408LDY-T1 Applications
There are a lot of Vishay Siliconix DG408LDY-T1 Analog Switches & Multiplexers ICs applications.
- Transmit
- Cross Connects
- SDH/SONET multiplexers
- ISDN NT1/TA
- Switching Systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- SONET/SDH ADM
- PCMCIA cards
- Residential Gateways, Home Gateway/Router