DG3540DB-T1-E1
| Parameters | |
|---|---|
| Factory Lead Time | 21 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-WFBGA |
| Number of Pins | 8 |
| Supplier Device Package | 8-MicroFoot™ (1.5x1.5) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 4Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Max Power Dissipation | 400mW |
| Base Part Number | DG3540 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 46 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 37 ns |
| -3db Bandwidth | 360MHz |
| On-State Resistance (Max) | 3.5Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 8pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 41ns, 37ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 200mOhm (Max) |
| Crosstalk | -66dB @ 10MHz |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG3540DB-T1-E1 Overview
Shipping overseas is convenient due to the electrical component's packing in 8-WFBGA. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature extended to -40°C~85°C TA. Unlike digital switches, these are based on SPST - NO/NC switching circuits. The multiplexer consists of 2 circuits. Try searching with DG3540 if you're looking for variants. An switch multiplexer with 4Ohm internal resistance has a value of 4Ohm. For functions related to 8 pins, please refer to the datasheets. A voltage higher than 5.5V should not normally be supplied to the switches. Analogue multiplexer with a Single supply type that is cost-effective. 1.8V should be the lowest voltage fed to the electronic component. In order to operate this switch device, it would need a current of 1nA. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA. Temperatures higher than 85°C are not recommended for operation of the analogue multiplexer. Suppliers offer a package with 8-MicroFoot? (1.5x1.5).
DG3540DB-T1-E1 Features
Switch Circuit: SPST - NO/NC
1nA Supply Current
-3db Bandwidth: 360MHz
DG3540DB-T1-E1 Applications
There are a lot of Vishay Siliconix DG3540DB-T1-E1 Analog Switches & Multiplexers ICs applications.
- Channelized and Unchannelized DS3 applications
- High-Voltage
- Private Branch Exchange (PBX)
- Intelligent PBX
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Cable Modem
- Battery Powered Instruments
- Multiplexers
- Avionics and Military Systems
- New designs requiring multiplexer functions