DG2741DQ-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 8Ohm |
| Terminal Finish | MATTE TIN |
| Additional Feature | VIDEO APPLICATION |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2741 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 3V |
| Number of Channels | 1 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.5V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 40 ns |
| On-State Resistance (Max) | 800mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 81pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 30ns, 28ns |
| Charge Injection | 5.8pC |
| Crosstalk | -89dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 50ns |
| Voltage - Supply, Single (V+) | 1.5V~3.6V |
| Normal Position | NO |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
DG2741DQ-T1-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. 8 terminations have been made so far. By its 1 channels, the electronic component provides high-quality output. An 1.8V voltage supply should allow the electrical part to be turned on and run. There are 8 pins injected into the electronic part body. Based on SPST - NO switching circuits, these analog multiplexers work. Try searching with DG2741 if you're looking for variants. There is 8Ohm internal resistance in this digital multiplexer. To find out what the 8 pins do, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. A voltage higher than 3.6V should not normally be supplied to the switches. Digital switch that provides Single power at a cost-effective price. It is recommended that the electrical component receives a voltage of 1.5V. This multiplexer would work with 10nA current. An analogue multiplexer drains from a single voltage supply at 1.5V~3.6V. A digital multiplexer may suffer damage if voltage is applied above 1μA. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. Operating voltages range from 3V. Operating the 2 inputs requires 2 inputs. This electrical component also includes additional features such as VIDEO APPLICATION.
DG2741DQ-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO
10nA Supply Current
Additional Features: VIDEO APPLICATION
DG2741DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG2741DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Multi-Line E1 Interface Cards
- Precision instrumentation
- Switching Systems
- Audio and video signal routing
- Audio and video routing
- DSLAMs
- Battery Powered Instruments
- Automatic test equipment
- Avionics
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads