DG2738DN-T1-E4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-UFQFN |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 8Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 190mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.4mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2738 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 2.3V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 60 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| -3db Bandwidth | 720MHz |
| On-State Resistance (Max) | 8Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 28 dB |
| Current - Leakage (IS(off)) (Max) | 10nA |
| Channel Capacitance (CS(off), CD(off)) | 4.4pF 3.8pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 60ns, 50ns |
| Charge Injection | 10.4pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -109dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 70ns |
| Voltage - Supply, Single (V+) | 2.3V~4.3V |
| Normal Position | NC |
| Height Seated (Max) | 0.6mm |
| Length | 1.4mm |
| RoHS Status | ROHS3 Compliant |
DG2738DN-T1-E4 Overview
As the electronic part is packed in 8-UFQFN, international shipping is convenient. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 1:1. Operational temperature extended around -40°C~85°C TA. Totally, there are 8 terminations. Due to its 1 channels, the electrical component produces high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. It is injected into the electrical part body with 8 pins. Multiplexers built on a SPST - NC switching circuit are built. The multiplexer consists of 2 circuits. DG2738 can be used to search for analog multiplexer variants. This digital multiplexer has 8Ohm internal resistance. Datasheets for 8 pin functions are available upon request. Multiplexer or Switches is a typical switch device. Users should never supply a voltage higher than 4.3V to a switch device. An effective Single supply digital multiplexer. A low voltage of 2.3V should be applied to the electronic component. 1μA current would be enough for this multiplexer to operate. A voltage of 2.3V~4.3V is required to drain this analog switch from a single voltage supply. Putting voltage greater than 1μA on the multiplexer may cause damage. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
DG2738DN-T1-E4 Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
-3db Bandwidth: 720MHz
DG2738DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2738DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Switching Systems
- Digital cross connects (DSX-1)
- Avionics
- SONET/SDH ADM
- Audio and video routing
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- SONET
- Signal routing between systems
- Remote Powered Equipment
- Data switching