CY74FCT2574TSOCTG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74FCT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74FCT2574 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.25V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.75V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 250MHz |
| Propagation Delay | 10 ns |
| Turn On Delay Time | 2 ns |
| Family | FCT |
| Current - Quiescent (Iq) | 200μA |
| Output Characteristics | 3-STATE WITH SERIES RESISTOR |
| Current - Output High, Low | 15mA 12mA |
| Max Propagation Delay @ V, Max CL | 6.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Output Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | ROHS3 Compliant |
CY74FCT2574TSOCTG4 Overview
20-SOIC (0.295, 7.50mm Width)is the packaging method. The Tape & Reel (TR)package contains it. T flip flop uses Tri-State, Non-Invertedas the output. JK flip flop uses Positive Edgeas the trigger. In this case, the electronic component is mounted in the way of Surface Mount. A 4.75V~5.25Vsupply voltage is required for it to operate. Temperature is set to -40°C~85°C TA. There is D-Type type of electronic flip flop associated with this device. The FPGA belongs to the 74FCT series. You should not exceed 250MHzin its output frequency. A total of 1elements are contained within it. As a result, it consumes 200μA quiescent current and is not affected by external forces. Currently, there are 20 terminations. If you search by 74FCT2574, you will find similar parts. The power source is powered by 5V. JK flip flop input capacitance is 5pF farads. It belongs to the family of electronic devices known as FCT. There is an electronic part mounted in the way of Surface Mount. As you can see from the design, it has pins with 20. A Positive Edgeclock edge trigger is used in this device. The part is included in FF/Latches. It is designed with a number of bits of 8. It reaches 5.25Vwhen the maximum supply voltage (Vsup) is applied. A normal operating voltage (Vsup) should remain above 4.75V. Considering its reliability, this T flip flop is well suited for TAPE AND REEL. The power supply is 5V. The flip flop has 2embedded ports. To operate, the chip has a total of 8 output lines.
CY74FCT2574TSOCTG4 Features
Tape & Reel (TR) package
74FCT series
20 pins
8 Bits
5V power supplies
CY74FCT2574TSOCTG4 Applications
There are a lot of Texas Instruments CY74FCT2574TSOCTG4 Flip Flops applications.
- Convert a momentary switch to a toggle switch
- Pattern generators
- Load Control
- Data Synchronizers
- Cold spare funcion
- Single Down Count-Control Line
- Frequency division
- Functionally equivalent to the MC10/100EL29
- Data transfer
- Synchronous counter