BTS133TCBUMA1
| Parameters | |
|---|---|
| Factory Lead Time | 18 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-263-3, D2Pak (2 Leads + Tab), TO-263AB |
| Number of Pins | 3 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| Series | HITFET® |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 2 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Additional Feature | SEATED HGT-NOM; SEATED HGT-CALCULATED |
| Technology | MOS |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | BTS133 |
| Pin Count | 4 |
| JESD-30 Code | R-PSSO-G2 |
| Number of Outputs | 1 |
| Output Voltage | 60V |
| Output Type | N-Channel |
| Interface | On/Off |
| Output Configuration | Low Side |
| Power Dissipation | 90W |
| Output Current | 7A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Halogen Free | Not Halogen Free |
| Drain to Source Voltage (Vdss) | 60V |
| Nominal Input Voltage | 10V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 60V Max |
| Max Dual Supply Voltage | 60V |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Output Peak Current Limit-Nom | 7A |
| Rds On (Typ) | 40m Ω |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Height Seated (Max) | 4.5mm |
| Width | 9.25mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
BTS133TCBUMA1 Overview
As you can see, it's packaged in the way of a Tape & Reel (TR).There is a package for it in the TO-263-3, D2Pak (2 Leads + Tab), TO-263AB package.This lighting drivere has a mounting type of Surface Mount.There is a General Purpose switch type associated with it.It is recommended that the temperature be set to -40°C~150°C TJ for reliable operation.In this LED driver, there are no outputs available.The LED driving board operates at Not Required volts.Voltage output is N-Channel volts at maximum.The BTS133 family consists of this type.The termination count is 2.3 pins are used for operation.There are 1 functions of the LED driver.Surface Mount is mounted in the way of this LED driving board.In total, it has 4 pins.This electrical component is part of the HITFET? series.This case results in a 7A output current.This LED driver can also produce SEATED HGT-NOM; SEATED HGT-CALCULATED.
BTS133TCBUMA1 Features
Additional features like SEATED HGT-NOM; SEATED HGT-CALCULATED
BTS133TCBUMA1 Applications
There are a lot of Infineon Technologies BTS133TCBUMA1 Power Switches ICs applications.
- Wearable Devices
- Telecom and Network Systems
- Notebook PC
- HDD and SSD
- Various applications equipped with buttons
- PC Card Hot Swap
- Wireless Modem Data Cards
- USB Power Distribution
- PDAs
- Low Voltage I/O System Power