ADG842YKSZ-500RL7
| Parameters | |
|---|---|
| Factory Lead Time | 8 Weeks |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 370mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 14.4μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG842 |
| Pin Count | 6 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 3.6V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Test Frequency | 100kHz |
| Power Dissipation | 14.4μW |
| Max Supply Current | 4μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 14 ns |
| Supply Type | Single |
| Bandwidth | 21MHz |
| Turn-Off Delay Time | 7.8 ns |
| On-State Resistance (Max) | 370mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 54 dB |
| Current - Leakage (IS(off)) (Max) | 200pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 160pF 160pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 14ns, 7.8ns |
| Insertion Loss (dB) | 0.2 dB |
| Charge Injection | 200pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 8.2ns |
| Voltage - Supply, Single (V+) | 1.65V~3.6V |
| Normal Position | NC |
| Height | 1mm |
| Length | 2.2mm |
| Width | 2.2mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG842YKSZ-500RL7 Overview
Shipping overseas is convenient due to the electrical component's packing in 6-TSSOP, SC-88, SOT-363. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Increasing operating temperature to around -40°C~125°C TA. Totally, there are 6 terminations. High-quality output is provided by the electronic component's 1 channels. In the case of a voltage supply of 2.5V volts, the electrical part can be powered up and run. It is injected into the electrical part body with 6 pins. Circuits based on SPST - NC switching are used to construct these analog switch ics. Try searching with ADG842 if you're looking for variants. A 370mOhm internal resistance characterizes this multiplexer. To find out what the functions of 6 pins are, please refer to their datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 3.6V. A cost-effective Single supply type analogue multiplexer. It is recommended that the electrical component receives a voltage of 1.65V. A voltage of 1.65V~3.6V is required to drain this analog switch from a single voltage supply. Put voltage above 4μA on the multiplexer to cause damage. This electrical part is compatible with 3.6V operating voltages. A 21MHz-bandwidth can be used for data transfer.
ADG842YKSZ-500RL7 Features
1 Channels
Switch Circuit: SPST - NC
Bandwidth: 21MHz
ADG842YKSZ-500RL7 Applications
There are a lot of Analog Devices Inc. ADG842YKSZ-500RL7 Analog Switches & Multiplexers ICs applications.
- Residential Gateways, Home Gateway/Router
- Private Branch Exchange (PBX)
- Automotive applications
- Routers
- Audio and video switching
- Fault Tolerant Systems
- Audio and video signal routing
- RGB switches
- Cable Modem
- Imaging