ADG823BRM-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 600mOhm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 3.6V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG823 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 2μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 16 ns |
| -3db Bandwidth | 24MHz |
| On-State Resistance (Max) | 600mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 52 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 85pF 98pF |
| On-state Resistance Match-Nom | 0.16Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 45ns, 16ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 160m Ω |
| Crosstalk | -82dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 67ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG823BRM-REEL Overview
Shipping overseas is convenient due to the electrical component's packing in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Operation at a temperature around -40°C~125°C TA. Totally, there are 8 terminations. A 2 channel electronic part produces high-quality output. When the electronic component is given a voltage of 3.6V, it should be turned on and run. This electronic part can be found in the 8 series. Based on SPST - NO/NC switching circuits, these analog multiplexers work. Try searching with ADG823 to find analog multiplexer variants. In this multiplexer, the internal resistance is 600mOhm. Datasheets for functions of 8 pins are available. The analog multiplexer shown here is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. Analogue multiplexers of the Single supply type that are cost-effective. A low voltage of 1.8V should be applied to the electronic component. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 2μA.
ADG823BRM-REEL Features
2 Channels
Switch Circuit: SPST - NO/NC
-3db Bandwidth: 24MHz
ADG823BRM-REEL Applications
There are a lot of Analog Devices Inc. ADG823BRM-REEL Analog Switches & Multiplexers ICs applications.
- Audio and video switching
- Battery-powered systems
- Power routing
- Precision test equipment
- Ultrasound
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- PBX interfaces
- PBXs
- Intelligent PBX
- Sample-and-hold systems