ADG417BR-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG417 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 9V |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 5V |
| Power Dissipation | 400mW |
| Throw Configuration | SPST |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 15V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 6pF 6pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 160ns, 100ns |
| Charge Injection | 7pC |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±15V |
| Height Seated (Max) | 5.33mm |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | Non-RoHS Compliant |
ADG417BR-REEL Overview
Due to its 8-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have a ratio of 1:1. Operation at a temperature around -40°C~85°C TA. Total terminations are 8. A high-quality output is provided by the electrical component's 1 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. As part of the design of the 8 series, this electronic part has been incorporated into the system. A SPST - NC switching circuit is used for these analog switches. Try searching for ADG417 variants of the analog switch ic. Internally, this switch multiplexer has a resistance of 35Ohm. The datasheets for the 8 pins explain the functions. A analogue multiplexer of this type is a Multiplexer or Switches. A voltage higher than 12V should not normally be supplied to the switches. In order for the electronic part to function properly, the lowest voltage should be 5V. For this switch, a dual supply voltage is feasible, but it must not exceed 15VFor dual power supplies, a voltage of at least 5V should be attached. This electrical part is compatible with 9V operating voltages.
ADG417BR-REEL Features
1 Channels
Switch Circuit: SPST - NC
ADG417BR-REEL Applications
There are a lot of Analog Devices Inc. ADG417BR-REEL Analog Switches & Multiplexers ICs applications.
- Cable PC
- T1/E1 Terminals
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Fiber to the Home
- PDH Multiplexers
- Cable Modem
- Residential Gateways, Home Gateway/Router
- Frame Relay Equipment
- Channel Banks