74AHC1G79GW,165
| Parameters | |
|---|---|
| Base Part Number | 74AHC1G79 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 1 |
| Number of Bits | 1 |
| Clock Frequency | 90MHz |
| Propagation Delay | 15.5 ns |
| Turn On Delay Time | 6.9 ns |
| Family | AHC/VHC/H/U/V |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 1μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 8ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 1.5pF |
| Number of Input Lines | 2 |
| fmax-Min | 70 MHz |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2014 |
| Series | 74AHC |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Type | D-Type |
| Terminal Finish | TIN |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
74AHC1G79GW,165 Overview
5-TSSOP, SC-70-5, SOT-353is the way it is packaged. The package Tape & Reel (TR)contains it. In the configuration, Non-Invertedis used as the output. In the configuration of the trigger, Positive Edgeis used. Surface Mountis occupied by this electronic component. It operates with a supply voltage of 2V~5.5V. -40°C~125°C TAis the operating temperature. D-Typeis the type of this D latch. FPGAs belonging to the 74AHCseries contain this type of chip. This D flip flop should not have a frequency greater than 90MHz. There is 1μA quiescent consumption. 5terminations have occurred. The object belongs to the 74AHC1G79 family. Power is provided by a 5V supply. The input capacitance of this T flip flop is 1.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. AHC/VHC/H/U/Vis the family of this D flip flop. There is an electronic part that is mounted in the way of Surface Mount. A total of 5pins are provided on this board. In this device, the clock edge trigger type is Positive Edge. An electronic part with 1bits has been designed. Normally, the supply voltage (Vsup) should be above 2V. Its flexibility is enhanced by 1 circuits. For high efficiency, the supply voltage should be set to 5V. It has 2lines.
74AHC1G79GW,165 Features
Tape & Reel (TR) package
74AHC series
5 pins
1 Bits
74AHC1G79GW,165 Applications
There are a lot of Nexperia USA Inc. 74AHC1G79GW,165 Flip Flops applications.
- Computers
- Consumer
- Single Down Count-Control Line
- 2 – Bit synchronous counter
- Shift Registers
- Power down protection
- Dynamic threshold performance
- Single Up Count-Control Line
- Bus hold
- High Performance Logic for test systems